FC Type Female Connector Stainless Steel 316L Tube Fitting Plumbing
Fitting High Quality Sanmin
Tube Fittings Description
The tube fitting is a mechanism used both to seal and to grip
tubing . The mechanical advantage and geometry of this kind of
fitting produces a leak – tight assembly .
To assemble , simply insert the tube into the complete assembly
until the tube bottoms – out against the shoulder of the fitting
body . The two ferrules are driven forward between the nut and
fitting body using the mechanical force created by rotating the nut
clockwise . The Back ferrule is driven against the tapered rear of
the front ferrule is driven by force into the tapered mouth of the
The rear ferrule is swaged radially inwards on the tube while
lifting the front ferrule out to form a full – faced seal on the
tapered surface of the body .
The 1-1/4 Turn of the nut from the hand tight position assures
consistent drive of the sealing members . This ensures an effective
seal against high pressure as well as ultra high vacuum conditions
Two different methods can be used to cut tubes :
1 . Tube Cuter
2 . Hacksaw
In order to cut the tube with a hacksaw and get square ends , the
tube must be cut with guide blocks
This method of cutting necessitates deburring of the tube ends.
Scratches on the tube might cause leaks . it is , therefore ,
important to handle the tube carefully to reduce the risk of leaks
Some Recautions to be taken
1.Tubes must not be dragged on the floor .
2.Tubes must not be dragged out of a tubing rack , especially in
case of large OD tubes
Use : This is a “ No- Go ” Gauge and should be used as follows :
Make up to fitting according to the following instructions : 1/4
inch ( 6mm ) , 3/8 inch , 1/2 inch ( 12mm ) – make up 1-1/4 turns
from finger tight . Check gap between nut and body , using the
appropriate sized gauge . If the gauge slides easily into the gap ,
tighten the nut further until gauge can not enter the gap
In applications where severe conditions and high pressure exist ,
we recommend the following installation procedures :
1. Check that the nut is finger tight
2. Insert the tube ( Up to the shoulder )
3. Rotate the nut with a wrench until the tube does not rotate freely
4. Mark position of the nut .
5. Rotate the nut 1-1/4 turns .
This method ensures that even if the tube O.D. is at the minimum
tolerance , the ferrules will be in contact with the tube for the
full 1-1/4 rotation.
In order to assure maximum fitting reliability and performance ,
great care should be given when selecting the tubing for each
Q: How much is our minimum order quantity ?
A: Our minimun quantity is 1 Piece .
Q: Could you offer the free samples ?
A: Yeah, we could offer the free samples based on special
customer.pre-production sample,production sample.
Q: What ' s your business scope ?
A: Our business scope is SMC type high quality cylinder , air
source treatment , solenoid valve ,water valve,steam valve,
mechnical valve ,foot valve,angle seat valve,anti-explosion
valve,pluse vlave, pneumatic valve ,hydraulic ball valve,hydraulic
ss ball valve,hydraulic check valve,hydraulic solenoid valve ,all
type of coil,lubrication pump and parts,SS316 fitting,quick coupler
, etc .
Q: What is the price of the product ?
A: Our prices are based on the size and type of material , if you
can give me the information ,
then we can give you an estimated price is for reference only . We
can do any size and any desgin .
Q: what types of products you can make ?
A: We can make many kinds of stainless steel materials and
brass,aluminum . Valve / solenoid valve / electric valve /
pneumatic valve and air cylinder products and so on .
Why choose us
1: High quality with competitive price .
2: Sample order & small quantity order is acceptable .
3: Customize according to your special request .
4: Provide free products information .
5: Reliable quality assured and active after-sell service
Fittings hose , Male female brass fitting , Male female fitting ,
Pipe fitting , Pipe fittings plastic , Plastic fitting , Pneumatic
fitting , Push fittings , Quick connect fitting , Quick connecting
, Quick coupling fittings , SS304 , Stainless steel fittings ,
Stainless steel pipe fittings , Tee tube fittings , Threaded
stainless steel fittings , Tube connector , Tube fitting , Pipe
Connection , Pipe Joint , Plasitc Quick , Couplers , Pneumatic
parts , Threaded Union , Fitting pneumatic , Push in fitting , Push
on fitting , Speed Controls , Stop fittings , Quick connecting tube
fitting , Speed Controls , Check Valves , Hand Valves , Ball Valves
, Hand Sliding fitting , Air control valve , Mini fitting , Push -
In Fitting , Transition fitting , Push on fitting , Compression
fitting , 316L Stainless steel fitting